How To Fix Socket Connect Error 10093 TutorialHome > Socket Error > Socket Connect Error 10093
Socket Connect Error 10093
WSA_QOS_EFILTERCOUNT 11021 Incorrect QoS filter count. WSAEPROCLIM 10067 Too many processes. Is it good to call someone "Nerd"? If you are using a name server(s), check whether the server host(s) are up (e.g. http://unordic.com/socket-error/socket-error-10093.html
Developer suggestions: You need to be prepared to handle this error on any functions that reference blocking sockets, or any calls to blocking functions, if you allow the user to cancel WinSock functions:
Socket Error 10054
The v1.1 WinSock specification doesn't list any errors for these functions. Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE but the connection has already been aborted (e.g. Trick or Treat polyglot Is it unethical of me and can I get in trouble if a professor passes me based on an oral exam without attending class? WSA_QOS_EOBJLENGTH 11022 Invalid QoS object length.
WSAECONNRESET 10054 Connection reset by peer. For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM. If so, then the application might have had a problem resolving the name (see suggestions at WSATRY_AGAIN for more information). Socket Error 10049 This has no network-relevant analog (although the "inode" reference could refer to a network file system entry).
An incorrect number of QoS FILTERSPECs were specified in the FLOWDESCRIPTOR. Any of the WinSock name resolution functions can fail with this error. The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections. WinSock functions:
A connection attempt failed because the connected party did not properly respond after a period of time, or the established connection failed because the connected host has failed to respond. Socket Error 10061 Connection Refused An invalid QoS flow descriptor was found in the flow descriptor list. See WSASYSNOTREADY for details. Berkeley description: A required address was omitted from an operation on a socket.
- OpenEdge 10.1x WindowsQuestion/Problem DescriptionSQL Server dies after error "Connection failure, accept() failed.
- In it's place, WinSock uses the error WSAENETUNREACH, exclusively.
- This would occur if WinSock aborts an established connection after data retransmission fails (receiver never acknowledges data sent on a datastream socket).
- WSA_QOS_EFLOWDESC 11026 Invalid QoS flow descriptor.
- Not the answer you're looking for?
- See also: WSAECONNRESET, WSAENETRESET, WSAETIMEDOUT WSAECONNREFUSED (10061) Connection refused.
What Is A Socket Error
With datastream sockets, don't call connect() more than once (use select() or WSAAsyncSelect() to detect connection completion). http://support.2brightsparks.com/knowledgebase/articles/213469-common-ftp-errors-and-socket-error-messages Thank you in advance! 2 posts LuckyLuke posted 3 years ago BUMP! Socket Error 10054 Generically, the error means the network system has run out of socket handles. Socket Error 10053 Networking activity on the local host has not been initiated.
Socket Error # 10039: There may be a problem getting the IP address for the hostname. this content WSA_QOS_NO_RECEIVERS 11008 QoS no receivers. Also, enter the hostname or IP address, not a URL, e.g. Downloads and tools Windows 10 dev tools Visual Studio Windows SDK Windows Store badges Essentials API reference (Windows apps) API reference (desktop apps) Code samples How-to guides (Windows apps) Learning resources Socket Error 10054 Connection Reset By Peer
If you are using implicit SSL then you probably need to use port 990 instead of port 21. WinSock functions: getsockopt(), setsockopt() Additional functions: Bad IP headers can cause routers and remote hosts to issue ICMP "parameter problem" messages, which result in a ENOPROTOOPT error on Berkeley-derived systems. Note: Although connect() and FD_CONNECT also have this error listed, the documentation specifically states that WSAEADDRNOTAVAIL is appropriate if INADDR_ANY is passed as a destination address. http://unordic.com/socket-error/socket-error-code-10093.html However, the WSAEPROTONOSUPPORT is another possible equivalent for WinSock to use in place of this error.
WinSock description: Same as Berkeley. Socket Error Codes Linux For example, the error can occur when an attempt is made to read from a file that is not open, to open an existing read-only file for writing, or to open I suggest you call only one time the WSAStartup (ex.
Additional functions: Any functions that takes a pointer as an input parameter: inet_addr(), inet_ntoa(), ioctlsocket(), gethostbyaddr(), gethostbyname(), getservbyname(), getservbyport(), WSAAsyncGetHostByName(), WSAAsyncGetHostByAddr(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber, WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSASetBlockingHook() WSAEHOSTDOWN (10064) Host is down.
A retry at some time later may be successful. Limitations to the REST API of Cloud storage services Cloud Service Status 550 Data channel timed out Estimated Time Left indicator during profile runs are inaccurate "Failed to scan files: Out An MX record is returned but no A record—indicating the host itself exists, but is not directly reachable. Socket Error 10061 Connection Refused Smtp Operations that were in progress fail with WSAENETRESET.
The name you have used is not an official hostname or alias. WinSock description: Same as Berkeley for host resolution. Ran out of disk quota. check over here WSAEDISCON 10101 Graceful shutdown in progress.
Reduce your problem to the minimum. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. WSA_QOS_EUNKOWNPSOBJ 11024 Unrecognized QoS object.
Any application that uses a blocking socket or calls any blocking functions must handle this error. Too many open sockets. At least one QoS send path has arrived. You can attempt to avoid the error by calling WSAIsBlocking() before making any WinSock function calls.
Join them; it only takes a minute: Sign up C++ Winsock 10093 error up vote 1 down vote favorite I'm trying to build a server in C++ which can accept multiple Not the answer you're looking for? Error: 10093Disconnecting dead server