How To Repair Snmp Error 2003 (Solved)

Home > Snmp Error > Snmp Error 2003

Snmp Error 2003

Contents

As to your queries: 1. There are no prerequisites except that SNMP is configured and turned on at the device's end. any assistance will be greatly appreciated. Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. http://unordic.com/snmp-error/snmp-2003-error.html

Best Regards. Free PRTG Download >> What is this? Also, In the post you have mentioned that Trap Sensor is to be added in local probe, but I found that No Sensors can be added to local probe from WebGUI Free PRTG Download >> What is this? https://kb.paessler.com/en/topic/9763-prtg-snmp-error-2003

Cisco Snmp Error 2003

Thanks for your help! It may help, but if the device responds with "No such name..."-error in these cases, there is very little PRTG can do, other than showing you the error. error prtg snmp Created on Jun 28, 2010 5:41:28 PM by dlivgard (0) ●1 Last change on Jun 29, 2010 2:09:18 PM by Daniel Zobel [Paessler Support] Permalink 3 Replies Accepted

The Uptime Sensor is working fine in PRTG 9. I can successfully add a SNMP Uptime Sensor to this port and the PRTG SNMP Tester says everything is okay. See More SonicWALL NSA Series Articles Feedback submitted. Snmp Error Codes Learn more Top Tags 5804× prtg 1858× snmp 1476× sensor 948× wmi 628× notifications 478× maps View all Tags SNMP error # -2003 after going over this entire knowledge base

Also the "No Such Name" snmp error. Prtg Snmp Error # -3 Please refer to the article How can I test the functionality of my SNMP device? Thanks and Warm Regards, Nutan. https://kb.paessler.com/en/topic/10213-snmp-error-2003 After changing the timeout value from 5 tot 30 seconds, this all went away.

Use at your own risk. Snmp Port Now it works. You are invited to get involved by asking and answering questions! Where do they come from?

Prtg Snmp Error # -3

Scan interval is set to 5 min. Add comment Created on Oct 26, 2015 11:36:58 AM by SBSnetwork (0) ●1 Permalink Votes:0 Your Vote: Up Down Hello there, What happens when you do an interface scan using our Cisco Snmp Error 2003 Please make sure that the "Retry" is enabled on "Failed Requests" in the "SNMP Compatibility Options" and you can try to slightly increase the "SNMP Timeout" in the "SNMP Credentials"-Settings (but Snmp Error 2007 I change it to: view systemview included .1 and re-started snmpd.

You are invited to get involved by asking and answering questions! this content This is because processes in the Sonicwall are weighted, and during busy times, priority is given to essential processes. Use at your own risk. SNMPUtil is a commandline tool, and you can scan for all available OIDs on the device. Prtg Snmp Tester

  1. I tried Adding a SNMP trap reciever too....jst in case if it could work..but bingo...............It didn't...Silly I am.
  2. I still have PRTG Traffic Grapher 6.2.2.984 installed on this same machine and the SNMP Traffic Sensor works fine on it.
  3. On my Linux box, in my snmpd.conf file there was a setting like this: view systemview included .1.3.6.1.2.1 This limits the systemview to OID's that fall under this section only.

Below is the error code . server-2008 snmp snmp-error#2003 Created on Oct 22, 2010 12:50:53 PM by orhen100 (0) ●1 Permalink 2 Replies Accepted Answer Votes:0 Your Vote: Up Down in the Servers SNMP Service security settings error-2003 prtg snmp Created on Sep 10, 2013 11:22:51 AM by piotr_malek (0) ●1 Permalink 4 Replies Votes:0 Your Vote: Up Down Hi, does the error appear and disappears without any http://unordic.com/snmp-error/snmp-error-code-2003.html Please Help.......

You are invited to get involved by asking and answering questions! alert error snmp Created on Oct 6, 2010 1:39:00 AM by jr3151006 (0) ●1 Permalink 4 Replies Accepted Answer Votes:0 Your Vote: Up Down Hello, first of all please check if Free PRTG Download >> What is this?

What response do you get?

On my production machine I am able to access other SNMP locations without any trouble. Lucia St. This error occurs day after day between 22:07 to 22:15 on SNMP sensors. If it works from the Tester and the Tester was used on the same machine as the PRTG Probe runs on, then the difference might be the user accounts under which

Workaround The work around is to raise the priority of the SNMP process on the Sonicwall. I even checked by SNMPTester and that is working really fine that means there is no blockage for SNMP on the network. Use at your own risk. http://unordic.com/snmp-error/snmp-tester-error-2003.html Add comment Created on Mar 23, 2016 7:24:00 AM by Gemeente Enschede (0) ●1 Permalink Votes:0 Your Vote: Up Down Hi there, PRTG supports paging for SNMP requests since PRTG Version

Best regards Add comment Created on Mar 9, 2012 3:22:58 PM by Konstantin Wolff [Paessler Support] Permalink Votes:0 Your Vote: Up Down Same result. Email To Email From Subject Information from Dell Software Support Message You might be interested in the following information For more information regarding support on your Dell Software Product, please visit See: How can I use PRTG’s trap receiver and what are its limitations?