(Solved) Smart Read Raw Error Rate Tutorial

Home > Error Rate > Smart Read Raw Error Rate

Smart Read Raw Error Rate

Contents

This typically indicates severe controller or bearing problem, but may be sometimes caused by power supply problems. Column 2 is the relatively standardized attribute name. you will see how HDD's are made, tested and how to really work. it's up to company X, so like he says above, it's not important unless you have many drives of the same kind and you see some odd trends........??????? Source

I have spent 3 weeks on this F*UCKING issue already and lost quite some business due to the shi*tty quality of WD's drive. or Self-Monitoring, Analysis and Reporting Technology Reference materials http://en.wikipedia.org/wiki/S.M.A.R.T. - all about S.M.A.R.T., from Wikipedia; recommended reading! Why was Washington State an attractive site for aluminum production during World War II? Furthermore, it is obvious that the raw value of WD's RRER attribute is not a sector count. http://askubuntu.com/questions/20393/how-do-i-interpret-hdd-s-m-a-r-t-results

What Is Raw Read Error Rate

S.M.A.R.T. Browse other questions tagged hard-drive smart or ask your own question. i had to pry off the metal retention clip thing on on of my sata cables before it would go in far enough, when i did that it pretty much cleared

  • This is a most universal measurement, on the scale from 0 (bad) to some maximum (good) value.
  • xkm121 2013-01-02 18:41:22 UTC #19 I have posted a thread in their support section.
  • However, I would now start to make more often backups and begin to plan a hard drive change.

The raid needing verification really depends on the hardware/software running the raid. and data corruption issues.. be caused by the controller? Raw Read Error Rate Fail I suspect that others do not report the number to avoid a lot of confusion, and questions for their tech support people.

Read Error Rate [Stores data related to the rate of hardware read errors that occurred when reading data from a disk surface] Reallocated Sector Count [When the hard drive finds a Raw Read Error Rate Fix The value of the read error rate is not he times that your driver failed, but some data struct that depends on your disk manufacturer. I was just looking at smartctl output from one of my disks, and it had a large number for Seek error rate attribute (note that I edited the output for readability): attributes on Wikipedia. [incomplete] 1 Raw_Read_Error_Rate This is an indicator of the current rate of errors of the low level physical sector read operations.

Nothing happens at this attribute. Raw Read Error Rate Failed To be honest, WD quality control is starting to piss me off. Zatick 2013-09-17 22:28:35 UTC #6 It seems unlikely that a drive will be replaced based on raw read error rate. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run.

Raw Read Error Rate Fix

I say this because, if you examine the SMART data posted by "WD10EARS", you will note that after 22264 counts the normalised value has fallen by only 5 points, from 200 http://www.tomshardware.com/answers/id-2264625/raw-read-error-rate-failure-pending-sectors.html More specifically, raw value of theSeek error rate attribute should be converted to hexadecimal and then upper 16 bits are number of errors, while lower 32 bits are total number of What Is Raw Read Error Rate Hot Network Questions What exactly is a "bad" "standard" or "good" annual raise? Raw Read Error Rate Western Digital Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the

The normalized and worst values haven't changed anyway, so the assesment is still OK in the SMART data. this contact form Badblocks found no errors in 8 passes. Why is the bridge on smaller spacecraft at the front but not in bigger vessel? Selective Self-test supported. Raw Read Error Rate 1

I was curious of you found any under warning or error with the title 'disk' You say you already looked so i 'll take your word for it but i'm surprised It happens. Might indicate either a controller or a spindle bearing problem. have a peek here Abstract definition of convex set Set removeAll is removing values from original source Should non-native speakers get extra time to compose exam answers?

Conveyance self-test routine recommended polling time: ( 2) minutes. Raw Read Error Rate Ssd The reason why I posted this question was because I started to realize that the HDD was noticeable slower than before. Awesome article, and I'll link it to Wikipedia because you have some information that is really useful and missing from Wikipedia article.Now onto tehhnical bit:I have this Seagate drive: ST3500413ASbut it

We highly recommend to look at these SMART attributes first.

That is is just mind shatteringly insane ! Thursday, January 17, 2013 Seagate disk SMART values... Generally, the only ones you can count on seeing are: 1, 3, 4, 5, 7, 9, 10, 187, 190 or 194, 193, 195, 197, 198, and 199. Read Error Rate Crystaldiskinfo Good work WD.

Short version: Raw_Read_Error_Rate has creeped up to 1 on a new WD Red after running SMART tests and badblocks. Opening the file manager could take even seconds, as well as opening other programs or files. The thing is the raw read error rate alone will NOT EVER lead to raid verification, if there is a fault with the drive that will lead to a verification of Check This Out And that has been said there MANY times also ! ..read it.

In other words, a drive with 0.6 million counts (errors ?) would still be passed by Data LifeGuard. I am more that pissed off right now. Be sure you understand how S.M.A.R.T should be read it snot always obvious. –Ramhound Jan 21 '15 at 23:37 The raw value isn't very meaningful by itself, and not Hardware recommendations • RAID5/RAIDZ1 is dead Read my guide!